The following is reproduced from: https://www.php.cn/linux-389431.html
This article mainly shares with you the method of configuring static ip under linux bridge mode, hoping to help you.
1: Bridging mode
VMware bridging mode is to connect the virtual network adapter of the virtual machine with the physical network adapter of the host. The virtual network adapter in the virtual machine can directly access the external network through the physical network adapter in the host. In short, it is like adding a new and independent computer to the local area network. Therefore, the virtual machine will also occupy an IP address in the LAN and can access each other with other terminals. Bridge mode network connection supports wired and wireless host network adapters. If you want to treat the virtual machine as a completely independent computer and allow it to communicate with other terminals, the bridge mode is usually the easiest way for the virtual machine to access the network.
2: Set up network adapter
3: Modify the configuration file and set the static ip address
1: Check the network card interface name ifconfig | more or ip addr | more
[root@localhost ~]# ifconfig | more eth0 Link encap:Ethernet HWaddr 00:0C:29:5A:71:6D inet addr:192.168.1.123 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe5a:716d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5631 errors:0 dropped:0 overruns:0 frame:0 TX packets:324 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:398905 (389.5 KiB) TX bytes:27775 (27.1 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230 errors:0 dropped:0 overruns:0 frame:0 TX packets:230 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:19722 (19.2 KiB) TX bytes:19722 (19.2 KiB)
2: Edit the network card file VIM / etc / sysconfig / network scripts / ifcfg-eth0
As shown in the above figure, my network card name is eth0, and the corresponding file name is ifcfg-eth0
[root@localhost ~]# vi /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 #Network card interface name BOOTPROTO=dhcp #System startup address Protocol DHCP: DHCP dynamic address protocol static: static address protocol HWADDR=00:0c:29:5a:71:6d IPV6INIT=yes NM_CONTROLLED=yes ONBOOT=yes #Whether to activate the network card interface when the system starts TYPE=Ethernet UUID="793813e9-4cbd-4ae1-a1de-f9f38b8369ee" USERCTL=no PEERDNS=yes
Then add the following content to the file
IPADDR=192.168.1.123 #Static ip. ping the ip before adding it. It can only be used if the ping fails to ensure its uniqueness NETMASK=255.255.255.0 #Subnet mask GATEWAY=192.168.1.1 #gateway
The complete configuration file is as follows
[root@localhost ~]# vi /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=static HWADDR=00:0c:29:5a:71:6d IPV6INIT=yes NM_CONTROLLED=yes ONBOOT=yes TYPE=Ethernet UUID="793813e9-4cbd-4ae1-a1de-f9f38b8369ee" USERCTL=no PEERDNS=yes IPADDR=192.168.1.123 NETMASK=255.255.255.0 GATEWAY=192.168.1.1
3: Restart network service network restart
[root@localhost Desktop]# service network restart Shutting down interface eth0: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: Active connection state: activating Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/9 state: activated Connection activated [ OK ]
4: Open cmd locally to test ping 192.168.1.123
C:\Windows\System32>ping 192.168.1.123 Is Ping 192.168.1.123 Data with 32 bytes: From 192.168.1.123 Reply from: byte=32 time=6ms TTL=64 From 192.168.1.123 Reply from: byte=32 time=30ms TTL=64 From 192.168.1.123 Reply from: byte=32 time=8ms TTL=64 From 192.168.1.123 Reply from: byte=32 time=8ms TTL=64
Relevant recommendations:
Detailed explanation of bridging mode of PHP design mode
The above is the details of how to configure static ip in linux bridging mode. Please pay more attention to other relevant articles on php Chinese network!
---------------------
The copyright of this article belongs to the author.
For commercial reprint, please contact the author for authorization. For non-commercial reprint, please indicate the source.
Source address: https://www.php.cn/linux-389431.html
Source: PHP Chinese website (www.php.cn)
© Copyright notice: Please attach the original link for reprint!